VOIP
- Upgrade the firmware of VigorIPPBX 3510 by Firmware Upgrade Program-TW
- Upgrade the firmware for VoIP module-TW
- Upgrade the System Prompt-TW
- Collecting VoIP logs from CLI-TW
- Designate a Outgoing WAN for SIP Traffic-TW
- Customize the Caller ID Type-TW
- Register the router to a SIP server-TW
- Use Phone Book to make VoIP calls over VPN-TW
- Make caller ID display or replace symbol ‘+’ -TW
- Prioritize VoIP Traffic by QoS
- Send the voice message by email-TW
- Dial VoIP call via IP address with Dial Plan-TW
- How to use Call Barring?-TW
- Control the Conversation Time for each Trunk by Time Budget-TW
- What do the SNR and Loop Att. values indicate?
- How can I disable the call waiting function for 2100V/2500V?
- Sometimes when I am on a call there is a beeping noise which is so loud that I cannot hear the other party.
- How can my VoIP router do Call Forwarding?
- My PC connects to the AP, however it doesn’t send or receive any packets once it has been authenticated
- Can I use a Fax machine on VoIP?
- What is meant by “Expiry Time”? I don’t want my VoIP calls to expire!
- VoIP – Digit Map
- VoIP – How do I connect FXS to PSTN-PBX?
- VoIP – How to enable Hotline function?
- How to forward incoming call to FXS port 2 while FXS port 1 is busy?
- How can I disable the G.729A/B codec (or any other specific codec)?
- Why is the CODEC used for a call not the one I select in Vigor VoIP configuration?
- Why is there an echo on my VoIP calls? How can I remove it?
- How to use the Digit Map
- How do I configure optimal DoS Defense settings to eliminate “skips” and “jitters” in VoIP conversations?
- How can I get the Console Log from a Vigor 3300?
- Can I use the Vigor3300V’s FXS and FXO ports as a PBX?
- How can I configure Vigor3300V’s FXO ports as Trunk lines for an Asterisk or Trixbox PBX?
- What are the differences in VoIP capabilities between Vigor models?
- Does Vigor V model support softphone and extension? How many extensions are supported?
- Can I attach my Cordless phone into the FXS port?
- How much bandwidth does VoIP actually require?
- What DTMF Mode should I use?
- Can I choose between SIP accounts for external calls by using a prefix? E.g. prefix of 9 to use SIP account 1; prefix of 8 to use SIP account 2; etc.
- How to configure a SIP Account
- Why am I experiencing very bad voice quality on VoIP?
- My VoIP calls cut off after a short time.
- Since I started using VoIP my Draytek router is logging multiple DoS attacks?
- Sometimes I can make VoIP calls, but sometimes I cannot.
- How to provide VoIP log to DrayTek engineers
- My company has VoIP for all staff, but at the moment only one PC can use the VoIP functionality.
- What are some common mistakes when setting up VoIP account(s) on Vigor routers?
- I can receive VoIP calls, but can’t call out
- The wireless connection between Intel Centrino laptop and Vigor2800G keeps dropping out when I use WPA-PSK/TKIP.
- Configuring QoS for VoIP device behind Vigor3300 Router
- How can I find my router’s uplink port?
- How to configure call forwarding
- Can I call between the two phone ports (intercom facility)?
- Configuring the Vigor2820 for FaktorTel VoIP Service
- How can I eliminate the pause before the Vigor places the VOIP Call?
- How to Transfer Calls or Make Internal Calls between Two FXS ports on Vigor Routers?
- Sample Configurations for VoIP
- How to Configure VoIP on Vigor3300V Router
- VoIP “dsp debounce” Command
- Does anyone know what causes the 2820vn to freeze when using a VoIP handset, NAS and Torrents at the same time?
- How does the PSTN Pass-Through Work on Vigor Routers Supporting PSTN connection?
- How to Configure VoIP on Vigor Router
- How to Hide Caller ID in Vigor Routers
- How to Install/Configure a Softphone
- STUN Server VOIP Configuration on Vigor Router
- I cannot get into my Vigor’s web configurator and the Dial-up Networking tries to dial continuously. What should I do?
- What does Call Scheduling do ?
- CLIR (hide caller ID) Not Working
- Ways to Debug VoIP Issues
- Answering machine not picking up VoIP calls
- Call Barring Function
- Changing Ring Pattern to Improve Caller ID Response Time
- Distorted Voice Quality when using VOIP
- DTMF Settings in Vigor Routers
- Custom Trunk How to Increase the Number of Trunk – Registering FXO/ISDN-TE port of 3300V+ to the Custom Trunk in VigorIPPBX
- An Introduction to SIP and debug logs
- What is SIP ALG?
- What is “T.38 Fax relay” service?
- Why can I not send more than one “#” key entry to VoIP phone on Vigor router?
- Can I call between the two phone ports on a 2830 router?
- How to Grab an unattended incoming Call
- Configuring Simtex VOIP SIP Trunk in VigorBX 2000
- Video – Vigor IPPBX 2820 User Prompts
- DrayTek IP PBX Configuration Tutorial
- Video – VigorIPPBX 3510 – VoIP over VPN in application
- Video – VigorIPPBX 2820 Auto Provisioning
- Video – VigorIPPBX 2820 configuration – Register extensions
- Setting up Voicemail in VigorBX 2000
- Maximum Number of IP Phones Connected to DrayTek Vigor2860 Router
- How to Disable SIP ALG on Draytek Routers
- How to Dial a Number That Includes “#” Character
- 2820IPPBX IVR Configuration Menu
- Configuration and Application for New Auto Attendant (AA)
- Problem Accessing iiNet Voicemail System
- How to enable and disable SIP ALG in linux based DrayTek Routers
- How to Disable VOIP Service in Vigor2820Vn Router
- How to Configure Vigor2830Vn so Incoming PSTN Calls Only Ring on Phone 1
- How to Switch Auto Attendant for Office and Non-Office Hours by using Extension
- VigorPhone 350 Speed Dial Setting
- How to Control the Conversation Time for each Trunk with Time Budget
- How to Configure and Use the Queuing Function in Hunt Group
- DIAL IN and OUT connection management screenshot
- Configuring VPN on iPhone (Whirlpool Post)
- Best VOIP settings for GOTALK
- How to configure the delay time before the VoIP number is dialled in Vigor Router
- Is there anyway I can configure my DrayTek to operate as a wireless ATA?
- Internal SIP device (ex. Linksys ATA, Elastix box) behind Draytek router won’t register.
- Engin VoIP call disconnects after 40mins
- An Introduction to VoIP “DialPlan” Configuration
- 2710 Caller ID not showing even after installing firmware 3.3.6.1
- What are the system and User prompts in the Vigor IPPBX
- Transferring a Call Using a Cordless Panasonic Analogue Phone
- How to configure and use the MWI on VigorIPPBX 2820
- VoIP Device Behind Vigor Router
- Why does PBX Auto answering machine fail to recognise my key presses?
- What is APSD?
- Transitioning Phone Services to the NBN
- VigorIPPBX Training Guide: Part 08
- VigorIPPBX Training Guide: Part 07
- VigorIPPBX Training Guide: Part 06
- VigorIPPBX Training Guide: Part 03
- VigorIPPBX Training Guide: Part 05
- VigorIPPBX Training Guide: Part 04
- VigorIPPBX Training Guide: Part 02
- VigorIPPBX Training Guide: Part 01
- How to Configure VoIP on Vigor Router (2765Vac/2865Vac/2866Vac)