The DrayTek Vigor2865L-5G series and Vigor2927L-5G series routers have an integrated 5G/LTE modem. They will accept SIM cards from any of the major broadband service providers in Australia – Telstra, Optus, Vodafone, etc., as well as those in New Zealand – Spark, 2Degrees, Vodafone, etc.
This guide will explain how to configure the Vigor2865L-5G and Vigor2927L-5G series routers to enable 5G/LTE communication via the integrated 5G modem.
In our example, we will use the Vigor2865Lax-5G, but the configuration details will be similar in the Vigor2865L-5G and Vigor2927L-5G series routers.
Supported 5G/LTE/WCDMA bands are:
- 5G NR Sub-6 SA Band: n1, 3, 5, 7, 8, 20, 38, 40, 77, 78
- 5G NR Sub-6 NSA Band: n1, 3, 5, 7, 8, 20, 38, 40, 77, 78
- 5G Max. Data Rate NR SA: 2.4Gbps (DL) / 900Mbps (UL)
- 5G Max. Data Rate NR NSA: 2.8Gbps (DL) / 555Mbps (UL)
- LTE FDD Band: B1, 3, 5, 7, 8, 20, 28
- LTE TDD Band: B38, 40
- LTE Category: Cat19 (DL) / Cat18 (UL)
- WCDMA (3G) Band: B1, 8
- WCDMA Max. Data Rate:
- 42Mbps (DL) / 5.76Mbps (UL)
Available LTE bands
These bands also apply to 5G.

For 3G/4G/5G coverage areas, check with your ISP for the exact frequency band used using the following links: Telstra, Optus, Vodafone and Virgin Mobile.
One helpful resource is the website https://www.rfnsa.com.au/
This site shows available services based on your postcode or address.
This configuration guide will cover the following:
- Optus
- Vodafone
- Telstra
Step 1: Insert the SIM Card into the Router
Remove the SIM Card slot cover plate on the router’s rear using a small Phillips head screwdriver.

The router has a dual SIM card slot, which can take two Nano-SIM cards placed on the carrier before being inserted into the SIM slot.
Notes:
- SIM 1 is the primary SIM slot, and SIM 2 will be the backup SIM slot.
- Only one SIM slot can be active at any time.
- Load balance over 2 SIMs is not supported.
Once the SIM card is installed, you can install the cover plate on the SIM card slot to prevent accidental removal.
The dual SIM slot allows you to use two mobile network providers. The router can switch to the secondary SIM card and cellular network connection if one mobile network fails.
It is also backward compatible with 4G LTE if a 5G network is unavailable.

Step 2: Attach Antennas to the Router
Since the antenna sockets are close together, you will need to use the antennas with the 1-metre leads; otherwise, you will not be able to fit all the antennas.
The box contains four antennas; you must fit each on the magnetic bases.
Now screw each of the leads into each socket on the router. These will be the four inner sockets. The two outside sockets on the wireless router are for the Wi-Fi antennas.
Refer to the image below:

For outdoor antenna installation, you must have at least two antennas connected. The sockets are the left socket nearest to the power switch on each pair.


Step 3 – Router Configuration
3.1 Enable LTE/5G WAN
Go to the WAN >> General Setup configuration menu.
For 5G-NR, set Active Mode to Always On. (Corresponds to WAN5).

Click on 5G-NR to go to the 5G-NR configuration menu.
- Select Yes to Enable
- Select mode for Link Condition Detection (Available modes: Ping Detect or HTTP Detect)
- Set Active mode to Always On
- Click on OK to save

3.2 – Enable 4G/5G WAN port
- Go to the WAN >> Internet Access menu
- Under Access Mode, click on the pulldown menu for 5G-NR WAN
- Select 3G/4G/5G Modem (DHCP mode).
- Click on the Details Page to configure the 5G-NR connection.

3.3– Configure 5G-NR
a. Select Enable to enable this profile.
b. Select the required Network Mode. Options are:
- 5G/4G/3G
- 4G Only
- 3G Only
We have selected 5G/4G/3G Network Mode.

c. Enter the APN (Access Point Name) to correspond with the service provider you will connect to.
You will need to disable Auto APN to allow you to enter the APN.

4.1 Optus 5G Configuration
Enter the required APN:
- connect
- yesinternet
- yesbusinessip (for business accounts with public IP address assignment)
Note: Some business accounts may require entering the username and password.

Click OK to save.
4.2 Vodafone 5G Configuration
Enter the APN: live.vodafone.com

Click OK to save.
4.3 Telstra 5G Configuration
Enter the required APN:
- telstra.internet
- telstra.extranet
- telstra.mms
- telstra.wap

Click OK to save.
Step 5 – Establishing a 5G connection
After completing the configuration steps outlined above, go to the Online Status>> Physical Connection router menu and check if the LTE/5G connection is up.
You may need to restart the router to bring up the connection.
Details will be shown under 5G-NR Status.
You should see that LTE/5G WAN has a valid IP address, the network status will be operational, and the signal quality will be shown.

You can check your Internet connectivity by going to an Internet webpage or running a ping test to an external site.
